Love Notes Table Runner
With vintage sheet music and lace, you can create inexpensive table runners that will add a gorgeous touch to your reception décor. The faded paper, musical notes, and ornate lace are an eclectic mix that enhances any DIY wedding design.
• Vintage sheet music
• Lace with a straight border
• Glue stick
• Hot glue gun
Step one: Measure the table you are creating the table runner for. Calculate the number of sheet music pages and the length of lace you will need, making certain to add several extra inches so that the lace will overlap the sheet music on all four corners of the runner.
Step two: Using a glue stick, add glue to the torn edge of one of the sheet music pages and secure the other sheet so that they overlap, covering the torn edge. Smooth the glued edge. Continue by gluing new sheets to cover the torn edges. All torn edges should overlap on the inside seam of the table runner with the clean edges as the border. Repeat these steps until the table runner is as long as you’d like it to be.
Step four: Using a pair of scissors, make a clean diagonal cut into one corner of the lace. Trim the sharp edge to make a nice scalloped edge. Add a dot of glue to the two cut corners and overlap them. Repeat this process for all four corners to finish the lace edging.
Special Note: Spread the love and gift these table runners to your bridal party to use in their own homes.
Lucky Horseshoe Table Numbers
These unique table numbers are absolutely perfect for a farmhouse wedding! Full of country charm, they will set the design for each table and add a rustic chic touch to your wedding décor.
• Old or rusty horseshoes
• Cedar wood (several planks, enough to back all of your horseshoes)
• Miter saw
• Rusty tin craft nails
• Wire cutters
• Rusty tin craft wire (18 or 22 gauge thickness)
• Needle nose pliers
• Wood burning torch
Step one: Measure each of your horseshoes. Have your local hardware store cut your wood to size, or cut the wood yourself using a miter saw.
Step two: Secure a horseshoe to each cedar wood piece using your rusty nails. Before you nail the horseshoe in place, make sure it is nice and centered.
Step three: To make each actual number, you will need to cut four 4 to 8-inch lengths of wire. Keep in mind that your wire length will vary depending on the number you are creating; an “8” will take more wire than a “1.”
Step four: Wrap the four lengths of wire together to make one twisted group; use the needle nose pliers if necessary.
Step five: Bend the wire into the shape of the number you are creating.
Step six: Curl the ends of each number, as this is where your nails will go through to secure it to the wood.
Step seven: Hammer the numbers to the wood pieces, using the rusty nails. Use as many nails as needed to ensure the number is securely in place.
Step eight: Scorch the edges of your table numbers with your wood torch to give it a rustic appearance. Make certain to follow the manufacturer’s safety guidelines!
These colorful rag balls make the most delightful decorations for a wedding ceremony! Instead of fresh flowers that can be costly, hang these rag balls from shepherd’s hooks lining the wedding aisle; they will bring texture, color, and balance to an open area.
• 4 yards assorted fabric
• Hot glue gun
• Twelve 6-inch Styrofoam balls
Step one: Cut your fabric into 16-inch squares. Using your scissors, cut a small slit at each end. Rip the fabric so it has a torn finish on all four sides. Make several small slits about 1 inch apart at the top of the fabric squares.
Step two: Rip the cut slits into long pieces.
Step three: Using one of the strips of ripped fabric, make it into a loop with the print facing outwards. Glue into place. This will be the handle for your rag ball.
Step four: Place a dot of glue on the back side of one of your strips of ripped fabric, and glue it onto the Styrofoam ball. Wrap the fabric around the ball and glue the other end onto the ball. Continue these steps until the Styrofoam ball is completely covered.